貝加萊通用混合模塊X20CM8281，奧地利貝加萊B&R全新原裝進口，特價優勢供應；主營品牌：博世力士樂（BOSCH-REXROTH）及安沃馳AVENTICS、迪普馬DUPLOMATIC、愛爾泰克AIRTEC、本特利Bently、貝加萊B&R、世格ASCO、阿托斯ATOS、派克。威格士。
 
貝加萊B&R模塊X20CM8281
物料號:
X20CM8281
描述:
數字和模擬通道
AI和AO的可選電流和電壓
計數器功能
該模塊為通用混合模塊。在這個模塊上，數字I/O和模擬I/O被組合在一起。根據需要，電流或電壓信號可用于模擬I/O。兩個數字輸入上的計數器功能擴大了使用范圍。
簡短說明
I/O模塊4個數字輸入、2個數字輸出、1個模擬輸入、1個數字輸出，具有特殊功能
一般信息
B&R ID代碼0x24C3
每個通道的狀態指示器I/O功能、操作狀態、模塊狀態
診斷
模塊運行/錯誤是，使用LED狀態指示燈和軟件
模擬輸入是，使用LED狀態指示器和軟件
數字輸出是，使用LED狀態指示器和軟件（輸出錯誤狀態）
電力消耗
0.01 W總線
內部I/O 1.75 W
致動器引起的額外功耗（電阻）[W]-
認證證書
CE是
UKCA是
ATEX 2區，II 3G Ex nA nC IIA T5 Gc
IP20，Ta（見X20用戶手冊）
09年ATEX 0083X
UL認證E115267
工業控制設備
HazLoc cCSAus 244665
過程控制設備
用于危險場所
I類，2區，ABCD組，T5
DNV溫度：B（0至55°C）
濕度：B（高達100%）
振動：B（4 g）
EMC:B（橋梁和露天甲板）
CCS是
LR ENV1
KR是
ABS是
BV EC33B
溫度：5-55°C
振動：4 g
EMC：橋梁和露天甲板
KC是
數字輸入
數量4
標稱電壓24 VDC
輸入特性符合EN 61131-2類型1
輸入電壓24 VDC-15%/+20%
24 VDC典型輸入電流。3.3毫安
輸入電路接收器
輸入過濾器
硬件≤2µs
軟件默認值為1ms，可在0到25ms之間配置，增量為0.2ms
連接類型1-wire連接
輸入電阻類型。7.18 kΩ
附加功能20 kHz事件計數、門測量
切換閾值
低<5 VDC
高壓>15VDC
通道和母線之間的絕緣電壓500Veff
事件計數器
數量2
信號形式方波脈沖
評估每個負邊，循環計數器
大輸入頻率。20千赫
計數器1輸入1
計數器2輸入3
計數器頻率大值。20千赫
計數器大小16位
閘門時間測量
數量1
信號形式方波脈沖
評估正邊緣-負邊緣
計數器頻率
內部48 MHz、24 MHz、12 MHz、6 MHz、3 MHz、1.5 MHz、750 kHz、375 kHz、187.5 kHz
計數器大小16位
脈沖之間的暫停時間≥100µs
脈沖長度≥20µs
支持的輸入輸入4
模擬輸入
數量1
通過不同的端子連接輸入±10 V或0至20 mA/4至20 mA
輸入類型單端
數字轉換器分辨率
電壓±12位
當前12位
轉換時間400µs，轉換與X2X鏈路周期異步運行
輸出格式INT
輸出格式
電壓INT 0x8001-0x7FFF/1 LSB=0x0008=2.441 mV
當前INT 0x0000-0x7FFF/1 LSB=0x0008=4.883µA
信號范圍內的輸入阻抗
電壓>1 MΩ
當前-
負載
電壓-
電流<300Ω
輸入保護電源電壓接線保護
允許的輸入信號
大電壓。±15v
大電流。±50毫安
過載時的數字值輸出
拍攝不足
電壓0x8001
當前0x0000
超過
電壓0x7FFF
當前0x7FFF
轉換過程逐次逼近
輸入濾波器二階低通濾波器/截止頻率1 kHz
大誤差
電壓
收益0.08%
偏移0.02%
當前
增益0至20mA=0.08%/4至20mA=0.1%
偏移0至20毫安=0.03%/4至20毫安=0.16%
大增益漂移
電壓0.01%/°C
電流0至20mA=0.009%/°C
4至20mA=0.0113%/°C
大偏移漂移
電壓0.002%/°C
電流0至20mA=0.004%/°C
4至20mA=0.005%/°C
非線性
電壓<0.02%
電流<0.02%
通道和母線之間的絕緣電壓500Veff
數字輸出
數量2
可變電流源FET
標稱電壓24 VDC
開關電壓24 VDC-15%/+20%
標稱輸出電流0.5A
總標稱電流1A
連接類型1-wire連接
輸出電路源
輸出保護過電流或短路時的熱關斷、開關電感負載的集成保護、反極性保護
診斷狀態輸出監測，延遲10ms
輸出關閉時的漏電流為5µA
RDS（開啟）105 mΩ
峰值短路電流<14A
過載停機或短路停機時打開電源。10ms（取決于模塊溫度）
切換延遲
0→1<250µs
1→0<270µs
開關頻率
大電阻負載。100赫茲
電感負載見“切換電感負載”一節。
關閉感應負載時的制動電壓。50伏直流電
通道和母線之間的絕緣電壓500Veff
模擬輸出
數量1
通過不同的端子連接輸出±10 V或0至20 mA
數字轉換器分辨率12位
轉換時間300µs，轉換與X2X鏈路周期異步運行
整個范圍內輸出變化的穩定時間為1ms
打開/關閉行為啟動和錯誤內部啟用繼電器
大誤差
電壓
增益0.04%
偏移0.0225%
當前
增益0.05%
偏移0.125%
輸出保護防短路
輸出格式
電壓INT 0x8001-0x7FFF/1 LSB=0x0010=4.882 mV
當前INT 0x0000-0x7FFF/1 LSB=0x0010=9.766µA
每個通道的負載
大電壓。±10 mA，負載≥1 kΩ
大電流。負載為400Ω
大增益漂移
電壓0.012%/°C
電流0.014%/°C
大偏移漂移
電壓0.0075%/°C
電流0.03%/°C
負載變化引起的錯誤
大電壓。0.02%，從10 MΩ→1 kΩ，電阻性
大電流。0.5%，從1Ω到400Ω，電阻
非線性<0.1%
通道和母線之間的絕緣電壓500Veff
電氣性能
電氣隔離
通道與總線隔離
通道未與通道隔離
操作條件
安裝方向
水平是
垂直是
安裝海拔高度
0至2000米無限制
>2000米每100米環境溫度降低0.5°C
防護等級符合EN 60529 IP20
環境條件
溫度
操作
水平安裝方向-25至60°C
垂直安裝方向-25至50°C
降額見“降額”一節。
儲存-40至85°C
運輸-40至85°C
相對濕度
運行5%至95%，非冷凝
儲存5%至95%，不凝結
運輸5%至95%，不凝結
機械性能
注意：單獨訂購1x接線端子X20TB12。
單獨訂購1x總線模塊X20BM11。
間距12.5+0.2mm

貝加萊數字量輸入/輸出
X20CM1201
X20CM8281
X20DM9324
X20RT8001
X20RT8201
X20RT8202
X20RT8401
貝加萊模擬量輸入
X20AI1744
X20AI1744-3
X20AI2222
X20AI2237
X20AI2322
X20AI2437
X20AI2438
X20AI2622
X20AI2632
X20AI2632-1
X20AI2636
X20AI4222
X20AI4322
X20AI4622
X20AI4632
X20AI4632-1
X20AI4636
X20AI8221
X20AI8321
X20AIA744
X20AIB744
X20AP3111
X20AP3121
X20AP3122
X20AP3131
X20AP3132
X20AP3161
X20AP3171
X20CM0985
X20CM0985-1
X20CM8281
X20RT8201
X20RT8401
貝加萊模擬量輸出
X20AO2437
X20AO2438
X20AO2622
X20AO2632
X20AO2632-1
X20AO4622
X20AO4632
X20AO4632-1
X20AO4635
X20CM8281
X20RT8202
X20RT8401
貝加萊溫度測量
X20AT2222
X20AT2311
X20AT2402
X20AT4222.
X20AT4232
X20AT6402
X20ATA312
X20ATA492
X20ATB312
X20ATC402
貝加萊電機控制器
X20MM2436
X20MM3332
X20MM4331
X20MM4455
X20MM4456
X20SM1426
X20SM1436
貝加萊其它功能
X20CM0985
X20CM0985-1
X20CM4323
X20CM4810
X20CM6209
X20CM8281
X20CM8323
X20CMR010
X20DS4387
X20DS438A
X20PD0011
X20PD0012
X20PD0016
X20PD2113
X20PS4951
貝加萊計數功能
X20CM1201
X20CM1941
X20CM8281
X20DC1073
X20DC1176
X20DC1178
X20DC1196
X20DC1198
X20DC11A6
X20DC1376
X20DC137A
X20DC1396
X20DC1398
X20DC1976
X20DC2190
X20DC2395
X20DC2396

貝加萊B&R電機電纜
物料號:
8CM015.12-3
描述:
可用于電纜拖鏈
專門組裝用于ACOPOS 1180/1320伺服驅動器和B&R伺服電機，電機連接器尺寸為1
電機電纜，長度15 m，4x 4 mm²+2x 0.75 mm²+2x 1 mm²，8針內螺紋Intercontec電機連接器尺寸1，可用于電纜拖鏈
一般信息
電纜橫截面4 x 4 mm²+2 x 0.75 mm²+2 x 1 mm²
耐久性耐油性符合HD 22.10附錄A和DIN EN 60811-404
證書E170315 cRUus AWM STYLE 21223 AWM I/II A/B 80°C 1000 V FT1
認證
CE是
UKCA是
UL cULus E225616
功率轉換設備
EAC是
電纜施工
電力線
數量4
電線絕緣PP
電線顏色黑色、棕色、藍色、黃色/綠色
變型鍍錫銅絞線
橫截面4 mm²
屏蔽號
擱淺否
信號線
數量4
電線絕緣PP
電線顏色白色、白色/紅色、白色/藍色、白色/綠色
變型鍍錫銅絞線
橫截面2 x 0.75 mm²+2 x 1 mm²
屏蔽成對單獨屏蔽，鍍錫銅編織，光學覆蓋率>85%，箔屏蔽
Stranding White with White/red and White/blue with White/green
帶填充元件和箔屏蔽的電纜絞合
電纜屏蔽鍍錫銅編織，光學覆蓋率>85%和箔屏蔽
外護套
材料TPU
橙色，類似于RAL 2003平面
標簽B&R 4 G 4+（2x0.75）C+（2x1）C C E170315 cRUus AWM STYLE 21223 AWM I/II A/B 80°C 1000 V FT1
連接器
型號8針內螺紋speedtec電機連接器，尺寸1.0
交配周期<500
觸點8（4個電源觸點和4個信號觸點）
連接時的防護等級符合EN 60529 IP66/67
電氣特性
工作電壓。1000真空（UL）
試驗電壓
電線-電線4 kV
屏蔽線4 kV
導體電阻
電力線≤5.1Ω/km
信號線0.75mm²：≤26.7Ω/km，1mm²：≤20Ω/km
絕緣電阻≥500 MΩ*公里
載流能力符合DIN VDE 0298第4部分表11
壁掛式30 A
安裝在導管或電纜管道中30 A
安裝在電纜橋架中30 A
環境條件
溫度
移動-20°C至+80°C
靜態-20°C至+90°C
機械性能
尺寸
長度15m
直徑15.4 mm±0.4 mm
彎曲半徑
單個彎曲>48 mm
移動>119毫米
拖動鏈數據
加速度。50 m/s²（取決于行進路徑的長度）
彈性周期≥5000000
速度。300米/分鐘
重量4.2 kg


貝加萊B&R旋變電纜
物料號:
8CR015.12-1
描述:
可用于電纜拖鏈
專門組裝用于ACOPOS伺服驅動器和B&R伺服電機
分解器電纜，長度15 m，3x 2x 24 AWG（19x 0.127），12針內螺紋Intercontec分解器連接器，9針外螺紋DSUB伺服連接器，可用于電纜拖鏈
一般信息
電纜橫截面3x 2x 24 19 AWG
耐久性符合VDE 0472第803部分的耐油性以及標準液壓油
認證UL AWM 20671型，90°C，30 V，E63216和CSA AWM，90°C.30 V，I/II A/B FT1 LL46064
認證
CE是
UKCA是
UL cULus E225616
功率轉換設備
電纜施工
信號線
數量6
電線絕緣特殊熱塑性材料
電線顏色白色/棕色、綠色/黃色、灰色/粉色
變型鍍錫銅絞線
橫截面24 AWG/19 AWG
屏蔽號
擱淺白色與棕色，綠色與黃色，灰色與粉色
電纜絞合用箔屏蔽將3對電纜絞合在一起
電纜屏蔽銅編織，光學覆蓋率≥90%，箔屏蔽
外護套
材料PUR
綠色，類似于RAL 6018平面
標簽B&R 3x2x24 AWG FLEX UL AWM STYLE 20671 90°C 30 V E63216 CSA AWM 90°C 30V I/II A/B FT1 LL46064
連接器
類型12針內螺紋Intercontec解析器連接器
交配周期<500
12
附加連接器9針公DSUB伺服連接器
交配周期：<200
：9
連接時的防護等級符合EN 60529:IP20
連接時的防護等級符合EN 60529 IP66/67
電氣特性
工作電壓≤30 Veff
試驗電壓
電線-1.5 kV電線
電線-屏蔽0.8 kV
導體電阻
信號線≤86Ω/km
絕緣電阻>200 MΩ*km
環境條件
溫度
移動-20°C至+80°C
靜態-20°C至+90°C
機械性能
尺寸
長度15m
直徑6.5 mm±0.2 mm
彎曲半徑
單個彎頭≥20 mm
移動≥50 mm
拖動鏈數據
加速度≤6 g
彈性周期>3000000
速度≤4 m/s
重量1.1 kg


貝加萊B&R電纜
物料號:
9A0017.02
描述:
零調制解調器電纜RS232，1.8米，用于連接UPS和IPC（9針內螺紋DSUB連接器-9針內孔DSUB連接器）
一般信息
認證
CE是
UKCA是
機械性能
尺寸
長度1.8米

貝加萊B&R電機電纜帶制動
物料號:
80CM15002.21-01
描述:
電機電纜，長度15 m，5x 0.75 mm²，2x 0.5 mm²，用于帶制動器的步進電機，電機側有4針和2針連接器，可用于電纜拖鏈，UL列出
一般信息
電纜橫截面5x 0.75 mm²+1x 2x 0.5 mm²
耐久性符合VDE 0472第803部分的耐油性以及標準液壓油
認證UL AWM樣式20234，80°C，1000 V，E63216和CSA AWM I/II A/B，90°C，1000V，F(xiàn)T2 LL46064
電纜施工
電力線
數量5
電線絕緣特殊熱塑性材料
電線顏色黑色、棕色、藍色、綠色、黃色/綠色
變型鍍錫銅絞線
橫截面0.75 mm²
屏蔽號
擱淺否
信號線
數量2
電線絕緣特殊熱塑性材料
電線顏色白色、白色/紅色
變型鍍錫銅絞線
橫截面0.5 mm²
屏蔽成對的單獨屏蔽、鍍錫銅編織、光學覆蓋率>85%和箔帶
白色與白色/紅色交織
帶填充元件和箔帶的電纜絞合
電纜屏蔽鍍錫銅編織，光學覆蓋率>85%，包裹在隔離膜中
外護套
材料PUR
橙色，類似于RAL 2003平面
標簽B&R 5x0.75+1x2x0.5 FLEX UL AWM STYLE 20234 80°C 1000 V E63216 CSA AWM I/II A/B 90°C 1000伏FT2 LL46064
電氣特性
試驗電壓
電線-電線3 kV
屏蔽線3 kV
導體電阻
電力線≤29Ω/km
信號線≤39Ω/km
絕緣電阻>200 MΩ/km
載流能力符合DIN VDE 0298第4部分表11
壁掛式13 A
安裝在導管或電纜管道中11.5 A
安裝在電纜槽中13.5 A
環境條件
溫度
移動-10至70°C
靜態-20至90°C
機械性能
尺寸
長度15m
直徑10.8 mm±0.4 mm
彎曲半徑
單彎頭>34 mm
移動≥85 mm
拖動鏈數據
加速度<60 m/s²
彈性周期≥3000000
速度≤4 m/s
重量0.26 kg/m

貝加萊B&R I/O供電電纜
物料號:
X67CA0P00.0002
描述:
電源連接電纜，4針，直，0.25米
簡短描述
附件電源連接電纜，4針，直，0.25米
一般信息
注：不含聚氯乙烯和硅樹脂
PWIS和無鹵素
耐久性良好的耐化學性和耐油性
阻燃劑
良好的紫外線和臭氧耐受性
簡短描述電源連接電纜，0.25米
類型連接電纜
電纜橫截面
AWG 4x 20 AWG
mm²4x 0.5 mm²
電纜施工
電纜屏蔽未屏蔽
外護套
材料聚氨酯（PUR）
性能CFC、鎘和無鉛
細絞線0.34 mm²（22 AWG）
6級（42x 0.1毫米/42x38 AWG）
顏色黑色
電線
電線絕緣聚丙烯（PP）9Y
電線顏色棕色、黑色、藍色、白色
性能CFC、鎘和無鉛
屏蔽號
類型無涂層銅ETP1
細絞線（42x 0.1 mm/42x 38 AWG），6級
絞合未絞合
電氣特性
標稱電流。40°C時每個EN/觸點4 A
每個UL/觸點3安
連接電壓。60伏交流/直流
工作電壓。60伏
符合IEC 61076-2的II類絕緣等級
導線電阻≤57Ω/km
絕緣電阻≥100 MΩ
操作條件
防護等級符合EN 60529
連接器/聯軸器IP67，僅當擰入時
環境條件
溫度
運輸-40至90°C
固定安裝-30至90°C
柔性安裝-25至60°C
機械性能
尺寸
長度0.25米
直徑5 mm±0.2 mm
彎曲半徑≥10倍外徑
拖動鏈數據
加速度。5 m/s²
彈性周期500萬
速度。3.3米/秒

貝加萊B&R I/O供電電纜
物料號:
X67CA0P20.0150
描述:
電源連接電纜，4針，直，15米
簡短描述
附件電源連接電纜，4針，直，15米
一般信息
注：不含聚氯乙烯和硅樹脂
PWIS和無鹵素
耐久性良好的耐化學性和耐油性
阻燃劑
良好的紫外線和臭氧耐受性
簡短說明電源連接電纜，15.0米
類型連接電纜
電纜橫截面
AWG 4x 20 AWG
mm²4x 0.5 mm²
電纜施工
電纜屏蔽未屏蔽
外護套
材料聚氨酯（PUR）
性能CFC、鎘和無鉛
細絞線0.34 mm²（22 AWG）
6級（42x 0.1毫米/42x38 AWG）
顏色黑色
電線
電線絕緣聚丙烯（PP）9Y
電線顏色棕色、黑色、藍色、白色
性能CFC、鎘和無鉛
屏蔽號
類型無涂層銅ETP1
細絞線（42x 0.1 mm/42x 38 AWG），6級
絞合未絞合
電氣特性
標稱電流。40°C時每個EN/觸點4 A
每個UL/觸點3安
連接電壓。60伏交流/直流
工作電壓。60伏
符合IEC 61076-2的II類絕緣等級
導線電阻≤57Ω/km
絕緣電阻≥100 MΩ
操作條件
防護等級符合EN 60529
連接器/聯軸器IP67，僅當擰入時
環境條件
溫度
運輸-40至90°C
固定安裝-30至90°C
柔性安裝-25至60°C
機械性能
尺寸
長度15m
直徑5 mm±0.2 mm
彎曲半徑≥10倍外徑
拖動鏈數據
加速度。5 m/s²
彈性周期500萬
速度。3.3米/秒

貝加萊B&R Link電纜
物料號:
X67CA0X01.0002
描述:
X2X鏈路連接電纜，0.25米
簡短描述
附件X2X鏈路連接電纜，M12，4針，直，0.25米
一般信息
注意無鹵素
耐久性阻燃
類型連接電纜
電纜橫截面
數據線
AWG 2x 24 AWG
mm²2x 0.25 mm²
電源線
AWG 2x 22 AWG
mm²2x 0.34 mm²
電纜施工
信號線
屏蔽鋁箔配對屏蔽
絞合雙絞線
電纜絞合0.35 mm²（AWG 22），帶填料
電纜屏蔽鍍錫銅編織，覆蓋率>85%
外護套
材料熱塑性聚氨酯（TPU）
特性無鹵素
顏色為紫色
電線
性能鍍錫銅絞線
鍍錫銅-ETB1型
數據線：細絞線（19x 0.13 mm）
供應線：細絞線（19x 0.15 mm）
電線顏色
數據線藍色、白色
電源線紅色、黑色
電線絕緣
數據線Cell聚乙烯（PE）
電源線聚丙烯（PP）
電氣特性
額定電壓250 V
標稱電流。40°C時為4 A/觸點
連接電壓。125伏交流/直流
工作電壓。250伏
符合IEC 61076-2的II類絕緣等級
導線電阻數據線：≤78Ω/km
供電線路：≤55Ω/km
絕緣電阻≥100 MΩ
操作條件
防護等級符合EN 60529
連接器/聯軸器IP67，僅當擰入時
環境條件
溫度
運輸-40至80°C
固定安裝-40至80°C
柔性安裝-25至60°C
機械性能
尺寸
長度0.25米
直徑6.9 mm±0.2 mm
彎曲半徑
固定安裝≥7.5x外徑7.0 mm
柔性安裝≥15x外徑7.0 mm
彎曲半徑≥15x外徑
拖動鏈數據
加速度。4 m/s²
彎曲周期。200萬
速度。3米/秒
重量0.063 kg/m

貝加萊B&R Link電纜
物料號:
X67CA0X21.0150
描述:
X2X鏈路連接電纜，15米
簡短描述
附件X2X鏈路連接電纜，M12，4針，直，15米
一般信息
注意無鹵素
耐久性阻燃劑
簡短說明X2X鏈路連接電纜，15.0米
類型連接電纜
電纜橫截面
數據線
AWG 2x 24 AWG
mm²2x 0.25 mm²
電源線
AWG 2x 22 AWG
mm²2x 0.34 mm²
電纜施工
信號線
屏蔽鋁箔配對屏蔽
絞合雙絞線
電纜絞合0.35 mm²（AWG 22），帶填料
電纜屏蔽鍍錫銅編織，覆蓋率>85%
外護套
材料熱塑性聚氨酯（TPU）
特性無鹵素
顏色為紫色
電線
性能鍍錫銅絞線
類型鍍錫銅ETB1
數據線：細絞線（19x 0.13 mm）
供應線：細絞線（19x 0.15 mm）
電線顏色
數據線藍色、白色
電源線紅色、黑色
電線絕緣
數據線Cell聚乙烯（PE）
電源線聚丙烯（PP）
電氣特性
額定電壓250 V
標稱電流。40°C時為4 A/觸點
連接電壓。125伏交流/直流
工作電壓。250伏
符合IEC 61076-2的II類絕緣等級
導線電阻數據線：≤78Ω/km
供電線路：≤55Ω/km
絕緣電阻≥100 MΩ
操作條件
防護等級符合EN 60529
連接器/聯軸器IP67，僅當擰入時
環境條件
溫度
運輸-40至80°C
固定安裝-40至80°C
柔性安裝-25至60°C
機械性能
尺寸
長度15m
直徑6.9 mm±0.2 mm
彎曲半徑
固定安裝≥7.5x外徑7.0 mm
柔性安裝≥15x外徑7.0 mm
彎曲半徑≥15x外徑
拖動鏈數據
加速度。4 m/s²
彎曲周期。200萬
速度。3米/秒
重量0.063 kg/m


貝加萊B&R UPS電源模塊
物料號:
9A0100.17
描述:
C型UPS電池箱（更換件），2x 12 V，4.5 Ah，用于電池單元9A0100.16
一般信息
電池
類型霍克獨眼巨人12 V 4.5 Ah
使用壽命長達15年
可變單電池（VRLA）
存儲期間的服務間隔每6個月收費1次
認證
CE是
UKCA是
UL cULus E115267
工業控制設備
電氣特性
標稱電壓12 V
容量4.5 Ah
電池充電數據
充電電流類型。二點八八一
環境條件
溫度
操作-40至80°C
儲存-65至80°C
運輸-65至80°C
相對濕度
運行5%至95%，無冷凝
儲存5%至95%，非冷凝
輸送5%至95%，無冷凝
機械性能
尺寸
寬度38毫米
長度205 mm
高度102 mm
重量約。3600克


貝加萊B&R端子排
物料號:
0TB103.91
描述:
電源使用一排3針接線板0TB03.9x。
概述
許可證    
CE    是
UL    cULus E115267
工業控制設備
HazLoc    cULus HazLoc E180196
工業控制設備
用于危險場所
I 類， 部門 2， 組 ABCD，T4
DNV GL    溫度: B(0 - 55 °C)
濕度: B（ 100）
振動: A(0.7 g)
EMC: B(電橋和開口板)
接線端子
備注    通過螺旋法蘭實現防震
依照 UL 的額定數據
電極數量    3 個（母頭）
夾緊裝置類型    作為彈簧端子的規格 
電纜類型    僅銅導線（不是鋁導線！）
網柵尺寸    5.08 mm
接口橫截面積    
AWG 導線    AWG 26 至 12
帶塑料套環的芯線末端套管    0.20 至 1.50 mm²
單芯    0.20 至 2.50 mm²
細芯    0.20 至 2.50 mm²
帶芯線末端套管    0.20 至 1.50 mm²
電氣屬性
額定電壓    300 V
額定電流     10 A / 觸點
容積電阻    ≤ 5 mΩ
使用條件
依照 EN 61131-2 的臟污程度    臟污程度 2

貝加萊B&R端子排
物料號:
0TB1111.8010
描述:
單排11引腳0TB1111螺紋卡箍用于連接各種B&R模塊。
接線板
注意：通過螺紋法蘭防止振動
標稱值符合UL
引腳數量11
接線板類型螺旋線夾
電纜類型只有銅線（沒有鋁線！）
節距3.5 mm
連接橫截面
AWG電線28至14 AWG
金屬絲端套，塑料覆蓋0.20至1.50 mm²
單線0.20至1.50 mm²
細絞線0.20至1.50 mm²
帶線端套管0.20至1.50 mm²
電氣特性
標稱電壓300 V
標稱電流10 A/觸點
接觸電阻≤4.2 mΩ


貝加萊B&R CF卡
物料號:
5CFCRD.1024-02
5CFCRD.1024-03
5CFCRD.1024-04
5CFCRD.1024-06
描述:
CompactFlash 1 GB ATA/IDE SanDisk
CompactFlash 1 GB Western Digital（SLC）
CompactFlash 1 GB B&R (SLC)
容量1 GB
數據保留期10年
數據可靠性<每讀取1014位1個不可恢復錯誤
終身監控是
MTBF>4000000小時（25°C時）
服務無
支持的操作模式PIO模式0-4，多字DMA模式0-2
連續閱讀
典型的8 MB/s
連續寫入
典型的6 MB/s
認證
CE是
UKCA是
UL cULus E115267
工業控制設備
DNV溫度：A（0至45°C）
濕度：B（高達100%）
振動：A（0.7 g）
EMC:B（橋梁和露天甲板）
耐力
SLC閃存是
擦除/寫入周期
典型>2000000
磨損平衡靜態
糾錯碼（ECC）是
S.M.A.R.T.支持編號
支持
硬件MP100/200、PP100/200、PPS00/400、PP500、PPC300、PPC700、PPC725、PPC800、Provit 2000、Provit 5000、APC620、APC680、APC810、APC820
操作系統
Windows 7 32位No
Windows 7 64位否
Windows嵌入式標準7 32位否
Windows嵌入式標準7 64位否
Windows XP版否
嵌入式Windows XP是
Windows嵌入式標準2009是
Windows CE 6.0是
Windows CE 5.0是
軟件
PVI Transfer≥V2.57（PVI Development Setup≥V2.5.3.3005的一部分）
B&R嵌入式操作系統安裝程序≥V2.21
環境條件
溫度
操作0至70°C
儲存-50至100°C
運輸-50至100°C
相對濕度
運行8至95%，無冷凝
儲存8至95%，非冷凝
運輸8%至95%，無冷凝
振動
操作值。16.3克（159米/秒²0-峰值）
存儲量。30克（294米/秒²0-峰值）
運輸量。30克（294米/秒²0-峰值）
震驚
操作值。1000 g（9810 m/s²0-峰值）
存儲量。3000克（29430米/秒²0-峰值）
運輸量。3000克（29430米/秒²0-峰值）
高程
操作值。24383米
機械性能
尺寸
寬度42.8±0.10 mm
長度36.4±0.15毫米
高度3.3±0.10 mm
重量11.4克

貝加萊通用混合模塊X20CM8281
X20CM8281 X20通用混合模塊,4個輸出端,24VDC,漏式,1線連接技術,2路數字量輸出,0.5 A,源式,1線連接技術, 1個模擬量輸入,±10 V或0-20 mA/4-20 mA,12-bit分辨率,1個模擬量輸出, ±10 V/0-20 mA,12-bit分辨率, 2個計數器可作為事件計數或門測量
 
貝加萊通用混合模塊X20CM8281
模塊（module）：完成特定功能的單元、部件或者子程序。
撥號連接由一個系列提供綜合業務數字網（ISDN）主要速率接口（PRI）基本速率接口（BRI）的網絡模塊；集成數字調制解調器、模擬調制解調器、高密度的異步接口插槽以及異步/同步串行接口網絡模塊。
貝加萊通用混合模塊X20CM8281

貝加萊8LS同步電機特點：
8LS三相同步電機
8LS系列三相同步電機是專為需要高動態特性和定位精度以及緊湊型結構應用而開發的的永磁電子換向同步電機。

NdFeB永磁體
正弦EnDat編碼器或旋變器作為反饋單元
現在可用功能安全編碼器
三相星型連接
尺寸緊湊，重量輕巧
良好的轉子構造，使轉動慣量***小化，保證了優異的動態特性
高負載能力/峰值扭矩
扭矩脈動低
高速時的高動態扭矩
壽命長，除軸承外所有電機部件免磨損
定子產生的功耗通過外殼直接轉移到法蘭上
預緊的深溝球軸承兩端密封并油脂潤滑
完整的電機產品線，堵轉扭矩范圍從0.2 Nm至115 Nm
采用兩個SpeedTEC圓形插頭進行電氣連接
由ACOPOS伺服驅動器或ACOPOSmulti驅動系統控制

8LS三相同步電機不能直接與電源連接，它們只能與ACOPOS伺服驅動器或ACOPOSmulti驅動系統組合起來進行工作！

貝加萊8LS同步電機首選伺服電機類型：
8LSA25.D8060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 40 mm; j6 A fit...
8LSA25.D8060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.800 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 40 mm; j6 A fit...
8LSA25.D9060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 40 mm; j6 A fit...
8LSA25.D9060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 40 mm; j6 fit...
8LSA25.R0060D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 40 mm; j6 A fit...
8LSA25.R0060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 40 mm; j6 A fit...
8LSA25.R0060D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 0.600 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 40 mm; j6 A fit...
8LSA25.R0060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 0.800 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 40 mm; j6 A fit...
8LSA35.DA030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm;...
8LSA35.DA030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DA060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DA060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DB030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DB030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DB060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.DB060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA35.EA030D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA030D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA060D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA060D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EA060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB030D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB030D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB060D000-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB060D200-0
Synchronous motor; number of pole pairs: 2 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.EB060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.R2030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; without holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.R2030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.R2060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA35.R2060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 2.300 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA37.DA030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DA030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DA060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DA060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DB030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DB030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DB060S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.DB060S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 80 mm; j6 A fit...
8LSA37.R2030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA37.R2030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA37.R2060D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA37.R2060D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 6000 rpm stall torque: 3.600 Nm; with brake; smooth shaft; angled connector (swivel); centering diameter 80 mm; j6 A fit...
8LSA44.DA030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DA060S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DA060S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DB030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DB030S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DB060S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.DB060S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA44.EA030D000-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA030D200-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA030D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA060D000-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA060D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA060D200-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EA060D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB030D000-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB030D200-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB030D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB060D000-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB060D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB060D200-0
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.EB060D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.R2030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.R2030D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.R2060D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA44.R2060D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 6.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA46.DA030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DA030S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DA060S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DA060S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DB030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DB030S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DB060S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.DB060S200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 95 mm; j6 A fit...
8LSA46.R2030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA46.R2030D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA46.R2060D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA46.R2060D200-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 6000 rpm stall torque: 10.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 95 mm; j6 A fit...
8LSA55.DA030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA55.DA030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA55.DB030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA55.DB030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA55.EA030D000-1
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EA030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EA030D200-1
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EA030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EB030D000-1
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EB030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EB030D200-1
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.EB030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.R2030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA55.R2030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 12.500 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA57.DA030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA57.DA030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA57.DB030S000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA57.DB030S200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 130 mm; j6 A fit...
8LSA57.R2030D000-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA57.R2030D200-3
Synchronous motor; number of pole pairs: 4 pairs; nominal speed: 3000 rpm stall torque: 20.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 130 mm; j6 A fit...
8LSA73.DA030S000-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA73.DA030S200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA73.DB030S000-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA73.DB030S200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA73.R2030D000-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 180 mm; j6 A fit...
8LSA73.R2030D200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 26.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 180 mm; j6 A fit...
8LSA75.DA030S000-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA75.DA030S200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA75.DB030S000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; no brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA75.DB030S200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel) single-cable solution; centering diameter 180 mm; j6 A fit...
8LSA75.R2030D000-3
Synchronous motor; number of pole pairs: 5 pairs; nominal speed: 3000 rpm stall torque: 43.000 Nm; no brake; smooth shaft; angled connector (swivel); centering diameter 180 mm; j6 fit...
8LSA75.R2030D200-3
Synchronous motor; number of pole pairs: 3 pairs; nominal speed: 3000 rpm stall torque: 40.000 Nm; motor with holding brake; smooth shaft; angled connector (swivel); centering diameter 180 mm; j6 A fit...
貝加萊通用混合模塊X20CM8281



標準型減速器獨特的積木式組合設計
標準型減速器是一級減速比i= 3，4，5，8和10，背隙為≤ 8 - ≤ 15弧分。此外，它還提供二級和三級設計。在產品線的頂端，特級型減速器系列提供背隙≤1弧分，并具有高輸出 扭矩。貝加萊標準型減速器系列可以為您提供市面上存在的所有同軸行星減速器的輸出形狀供您選擇。
這使貝加萊在無需更改機器的情況下就能為現有的應用提供減速器。
就8GP55系列而言，在不需要極端小的背隙的應用中，可以將8GP60的輸出軸承和輸出形狀與標準的扭矩結合。這樣可以以經濟高效的方式解決高軸向力和徑向力。
標準系列中背隙足夠的情況下，在需要更高軸承力的應用中，它提供了經濟高效的解決方案。
貝加萊通用混合模塊X20CM8281
貝加萊ACOPOS。
1.ACOPOS CPU模塊
8AC140.60-2,插入模塊, CPU, 兼容 x86 100 MHz Intel , 16MB DRAM, 32kB SRAM, 應用軟件內存可更換: Compact-Flash, 1個CAN接口, 1個Profibus-DP從站接口, 1個RS232接口. 需單獨訂購應用軟件內存!
8AC140.61-2,插入模塊, CPU, ARNC0, 兼容 x 86 100 MHz Intel, 16MB DRAM, 32kB SRAM, 應用軟件內存可更換:
CompactFlash, 1個CAN 接口, 1個 Ethernet接口, 1個Profibus-DP從站 接口,, 1個RS232 接口. 需單獨訂購應用軟件
內存!
8AC141.60-2,插入模塊, CPU, 兼容x 86 100 MHz Intel, 16MB DRAM, 32kB SRAM, 應用軟件內存可更換: Compact-Flash, 2個CAN 接口,1個X 2X接口, 1個Ethernet接口, 1個RS232 接口, 需單獨訂購應用軟件內存!
8AC141.61-2,插入模塊, CPU, ARNC0, 兼容x86 100 MHz Intel, 16MB DRAM, 32kB SRAM, 應用軟件內存可更換:
CompactFlash, 2個CAN 接口, 1個X2 X 接口, 1個Ethernet接口, 1個RS232 接口, 需單獨訂購應用軟件內存!
2.ACOPOS I/O模塊
8AC130.60-1,插入模塊, 8個數字量 I/O可成對配置為 24V 輸入或 400/ 100mA輸出, 2個數字量輸出 2A, 需單獨訂購TB712端子排
8AC131.60-1,插入模塊, 2個模擬量輸入±10V, 2個數字量 I/O，可作為 24V輸入或 45mA輸出, 需單獨訂購TB712 端子排
3.ACOPOS編碼器模塊
8AC120.60-1,插入模塊, EnDat編碼器和正弦增量編碼器接口
8AC122.60-2,插入模塊, 旋變接口
8AC123.60-1,插入模塊, 增量編碼器和 SSI絕對值編碼器接口
4.ACOPOS網絡模塊
8AC110.60-2,插入模塊, CAN 總線接口
8AC112.60-1,插入模塊, ETHERNET Powerlink 接口
5.ACOPOS 伺服驅動
8V1010.50-2,伺服驅動 3x 110- 230V / 1?x? 110- 230V?? 2.0A ?0.45?kW, 集成線路濾波器，制動電阻和安全重啟抑制
8V1016.50-2,伺服驅動 3x 110- 230V / 1?x? 110- 230V?? 3.2A ?0.7?kW, 集成線路濾波器，制動電阻和安全重啟抑制
8V1010.00-2,伺服驅動 3x 400- 480V ?1.0A ?0.45 kW, 集成線路濾波器，制動電阻和安全重啟抑制
8V1016.00-2,伺服驅動 3x 400- 480V ?1.6A ?0.7 kW, 集成線路濾波器，制動電阻和安全重啟抑制
8V1022.00-2,伺服驅動 3x 400- 480V ?2.2 A ?1kW,集成線路濾波器，制動電阻和安全重啟抑制
8V1045.00-2,伺服驅動 3x 400- 480V ?4.4 A ?2kW,集成線路濾波器，制動電阻和安全重啟抑制
8V1090.00-2,伺服驅動 3x 400- 480V ?8.8 A ?4kW,集成線路濾波器，制動電阻和安全重啟抑制
8V1180.00-2,伺服驅動 3x 400- 480V ?19A ?9kW, 集成線路濾波器，制動電阻和安全重啟抑制，DC總線電源
8V1320.00-2,伺服驅動 3x 400- 480V ?34A ?16kW, 集成線路濾波器，制動電阻和安全重啟抑制，DC總線電源
8V1640.00-2,伺服驅動 3x 400- 480V ?64A ?32kW, 集成線路濾波器，制動電阻和安全重啟抑制，DC總線電源
8V128M.00-2,伺服驅動 3x 400- 480V ?128A ?64kW, 集成線路濾波器，制動電阻和安全重啟抑制，DC總線電源
貝加萊通用混合模塊X20CM8281